A ball screw that meets the catalog load rating can still fail to deliver the required cycle time or positioning performance. Long travel can make critical speed the limiting factor; a short lead can demand excessive motor speed; and a tight lead-accuracy specification cannot compensate for deflection in the bearings or machine frame.
The selection should therefore begin with the complete motion profile and an allowable error budget, not with diameter alone. Load, speed, lead, preload, support arrangement, and lubrication interact, so a satisfactory choice is the one that remains within its limits throughout the duty cycle—not merely at one nominal operating point.
Determine the axial force for each part of the cycle: acceleration, constant-speed travel, deceleration, dwell, and any process operation. The required force can include payload inertia, guide friction, external process force, and the component of weight acting along the axis. On a vertical axis, gravity changes the load differently during upward and downward motion; it must not be omitted from the holding condition.
A simplified starting point is:
Axial force = moving mass × acceleration + friction + process force + gravity component
The signs of these terms depend on direction. Calculate each operating segment separately rather than adding every maximum as though it occurs simultaneously. At the same time, include credible peak conditions such as emergency deceleration or a process jam when checking static capacity and structural strength.
For a repeating cycle, fatigue life depends on the load and the distance traveled under that load. For segments evaluated on a travel-distance basis, an equivalent load can be calculated as:
Feq = [Σ(Fi3 × si) / Σsi]1/3
Here, Fi is the axial load magnitude and si is the distance traveled in each segment. Use the screw manufacturer’s method where it differs, particularly for complex duty cycles or combined loading. A brief high-load segment can have a disproportionate effect because load is cubed in the calculation.
The basic rating life relationship for a ball screw is commonly expressed as L = (C/Feq)3 in millions of revolutions, where C is the basic dynamic load rating and Feq is the equivalent dynamic load. Multiply revolutions by lead to estimate travel life, using consistent units. This is a fatigue-life calculation under defined assumptions, not a guarantee against contamination, inadequate lubrication, corrosion, or installation damage.
Check the basic static load rating separately for stationary loads and peak events. Also check the screw shaft, support bearings, nut attachment, and machine structure: a nut’s static rating does not establish the allowable load of the entire axis.
Lead is the axial travel produced by one screw revolution. It links linear speed directly to rotational speed:
Screw speed (rpm) = linear speed (mm/min) ÷ lead (mm/rev)
For example, an axis moving at 30,000 mm/min requires 3,000 rpm with a 10 mm lead, but 1,500 rpm with a 20 mm lead. The larger lead can help a long axis remain below its speed limits. It also requires more drive torque for the same axial force, before acceleration and losses are considered.
An estimate of driving torque is T = F × l / (2πη), where F is axial force, l is lead in meters per revolution, and η is the efficiency for the relevant operating condition. Add torque for accelerating the rotating inertia of the screw, coupling, motor, and any transmission. Check both peak torque for acceleration and continuous or RMS motor torque for the full cycle, including thermal limits.
A larger lead also increases linear travel per motor revolution. Encoder resolution may remain adequate, but compliance, drive tuning, and feedback location still affect actual positioning. Conversely, a smaller lead is not automatically more accurate: it may force the screw to rotate too fast or increase cycle time.

Rotational speed is constrained by both the nut assembly’s permissible speed and the screw shaft’s critical speed. Critical speed is associated with lateral vibration or whirling and depends on shaft root diameter, unsupported length, end-support arrangement, and installation conditions. A support bearing arrangement described as “fixed” in a drawing must provide the stiffness assumed in the calculation; a flexible housing can reduce the benefit.
Use the manufacturer’s critical-speed calculation and recommended operating margin. Do not assume that a catalog maximum rpm applies to every shaft length. Check the worst operating position where unsupported length varies with nut position, and account for the actual shaft geometry rather than using nominal outside diameter indiscriminately.
For a long, fast axis, increasing shaft diameter can improve the speed limit and stiffness, but it also increases rotating inertia and motor acceleration demand. Other possibilities include a larger lead, a different support arrangement, an intermediate support where travel permits, or a rotating-nut design that keeps the screw stationary. Each changes packaging and bearing requirements; none removes the need to check nut speed and thermal behavior.
On compression-loaded axes, shaft buckling is a separate limit. It depends on unsupported length, root diameter, load direction, and end conditions. A screw can pass the critical-speed check and still lack sufficient buckling margin, especially on a long vertical axis carrying a heavy load.
Lead accuracy describes the deviation of actual travel from nominal travel over a stated length under specified measurement conditions. It is not the same as repeatability, backlash, or the accuracy of the finished machine. Compare screw accuracy specifications only when the measurement length, reference conditions, and acceptance criteria are compatible.
End-position error can include screw lead deviation, axial elastic deformation, support-bearing displacement, nut and mounting compliance, thermal expansion, and feedback or control error. Some contributions vary with load or direction, while others change with temperature or position. Assign an allowance to each significant source before selecting a screw accuracy grade.
For an initial stiffness estimate, axial screw deflection follows δ = FL/(AE), where F is axial load, L is the effective loaded length, A is the relevant shaft cross-sectional area, and E is the elastic modulus. The effective length changes with nut position and the support arrangement. Add the compliance of the nut, bearings, mounts, and frame; shaft stiffness alone can overstate axis stiffness.
Thermal effects deserve particular attention on long strokes or high-duty axes. A screw can change temperature through ambient conditions, bearing and nut friction, or heat transfer from nearby equipment. Fixed-end pre-tensioning and controlled thermal conditions may reduce some effects, but support design must accommodate the resulting forces. A linear encoder can measure table position directly, although it cannot eliminate mechanical compliance or guarantee stability without suitable control tuning.
Backlash is lost motion when the direction of axial load reverses. Preloaded nut arrangements reduce internal clearance and improve stiffness around reversal, which can benefit contouring or bidirectional positioning. The required preload depends on the working load, accuracy target, and manufacturer’s design; it should not be selected solely because the highest available value appears more precise.
Excessive preload increases frictional torque and heat and can reduce fatigue life. Insufficient preload may allow separation or loss of the intended stiffness under reversing loads. Evaluate preload alongside support-bearing clearance, coupling compliance, and the rigidity of the nut mount: removing clearance inside the nut does not remove lost motion elsewhere.
Rolled and ground screws are manufacturing categories, not complete performance specifications. A rolled screw may satisfy an application’s measured travel and repeatability requirements, while another application may justify a tighter ground-screw specification. Compare the supplier’s stated accuracy, preload, surface condition, and inspection basis rather than treating the manufacturing method as a guarantee of axis performance.
Lubrication affects rolling-contact life, friction, temperature, and corrosion protection. Select grease or oil according to the nut design, speed, load, temperature, and replenishment method. A lubricant suitable for a slow, intermittent axis may not provide the required distribution or heat management at higher duty. Confirm both the initial fill and the relubrication interval with the supplier’s guidance and the actual operating conditions.
Contamination protection must also fit the environment. Wipers help limit debris entering the nut, but exposed screws near chips, abrasive dust, washdown, or welding spatter may need covers or bellows. Protection adds space and can restrict travel or influence heat removal. Check chemical compatibility and corrosion exposure rather than assuming standard seals provide environmental isolation.
On a vertical axis, do not rely on the ball screw to hold the load when power is removed. Ball screws can back-drive, and behavior depends on lead, efficiency, load, and system friction. A brake, counterbalance, or other safety measure should be selected through the machine’s risk assessment; a motor holding brake alone must be assessed for its intended function and failure conditions.
A useful comparison uses the same cycle, moving mass, stroke, support positions, and environmental assumptions for every candidate. Request calculations or documented limits for dynamic life, static loading, critical speed, buckling where applicable, and nut speed. Review motor torque and inertia as part of the assembly rather than leaving them until after the mechanical selection.
The preferred option should also have a credible accuracy budget across the working stroke and temperature range. If a candidate meets nominal positioning requirements only when bearing compliance, thermal growth, or reversal effects are excluded, its apparent accuracy margin is not yet demonstrated. The final specification should state the required travel accuracy and inspection basis, preload or backlash condition, mounting interfaces, lubrication provisions, and operating duty so that the delivered assembly can be evaluated against the same assumptions used to select it.
Related News